• Read and understand this manual and its safety instructions before using this product. Failure to do so can result in serious injury or death.

• Follow all the instructions to avoid electric shocks or other hazards that may result in property damage and/or severe or fatal injuries.

• To use this product you must fully read and understand the contents of this user manual or Artome M10 - Quick User Guide.

• To connect Artome M10 with additional appliances, such as microphones, external speakers, and wireless collaboration devices, you must fully read and understood the contents of this user manual .

• Keep all safety information and instructions for future reference and pass them on to the next users of the product.

To prevent personal injury or damage to property, the following symbols are used to show dangerous operation or handling. Make sure you understand them properly when reading the guide.

This chapter lists possible danger situations concerning forbidden substancies, danger to senses and other dangers.

This chapter describes different situations and issues that may cause a risk of electric shock that may be lethal. These include unsuitable usage environment, electronic or mechanical damages, unauthorized disassembly,  unapproved power source or power cord or foreign objects on or inside the projector

•  Never plug Artome to the outlet before the projector is installed and Artome unit is fully configured with Artome Virtual Installer application.
  Contact your dealer to carry out the installation work.

• Do not use microphones that are not supported by Artome.
  The microphone may not work properly and may cause distortion or feedback. Ask for supported microphones from your dealer or manufacturer.

• Do not transport the device without proper protection
  The unit may be damaged. Always cover the unit with hardcase (optional accessory), when unit is moved in a car or by freight company.

• Do not store the device without proper protection from dust
  The dust may damage the product when it is used again. Use included carton box for storing.

• Do not move the device without proper protection from dust
  The dust may damage the product when it is used again. Use included carton box for storing

• Do not move the appliance on uneven or bumpy surfaces.
  Castors may be damaged

This chapter lists the rest of the graphical symbols used on the product or elsewhere.

Risk of Electrical Shock. Do Not Open! The voltage level in this equipment may be lethal. No user serviceable parts inside. For service, refer to qualified service personnel. 

 — This symbol is intended to alert the user to the presence of uninsulaterd "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric sock to persons.

— This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompnying the appliance

 The CE Marking on the product is the manufacturer's declaration that the product complies with the essential requirements of the relevant European health, safety and environmental protection legislation. The number behind the CE mark is the identification number of the notified body where the conformity assessment procedure s is applied. Notified body is not mandatory for Class I equipment

The symbol on the product, the accessories, or packaging indicates that this device must not be treated as unsorted municipal waste but must be collected separately.

Read and understand the manual and its safety instructions before using this product.

Artome M10 is a smart furniture that has an integrated laser projector, embedded sound system, and a videoconferencing feature.

Artome M10 is designed for easy presentation, multimedia experience or hybrid working. Artome M10 is an all-in-one product for any space due to its portability and fully adaptable image size, with automated use and the basic control panel.

A laminated Artome M10 - Quick User Guide inside the Artome M10 is intended for the users who want to get more out of connectivity and get more operational or other info. 

Basic User Guide is also available to learn about the product and to get started with it.

Artome M10 is intended to be used as a local presentation device or as the mobile all-in-one solution in different videoconferencing events. The product includes a pre-installed Epson projector for displaying scalable image for different surfaces, embedded sound system which consists of embedded mixer, an active speaker system, and connections for videoconferencing devices.

The Artome M10 is compatible with the following Epson projector models:

The User’s Guide of the selected projector is provided with Artome M10 if it is included in Epson package. Please notice that the Epson projector can only be installed by Artome or an authorized partner of Artome.

Artome M10 is high class audiovisual technology integrated with a piece of furniture that can be customized with different cabinet surface finishes and upholstered door with range of colors.

Artome M10 is made of birch plywood, MDF, PES fabric, steel, and aluminum.

This chapter contains information about:

• video projections and signals

• sound system 

• wireless connections 

• videoconferencing

• hybrid events and hybrid learning 

Artome M10 image features are based on Epson laser projector platform. All the features can be used with Epson’s own user interface. However, the main functions such as Projector On/Off, Freeze, AV Mute, and Zoom in/out functions can be controlled by the Artome M10 user interface. For example, if the projector is switched on with Epson user interface or by a third-party system, Artome M10 unit identifies the function and powers on.

Artome M10 takes care of the ventilation of the projector by letting the cool air in and warm air out through its built-in ventilation system. The projector also has a temperature sensor as a safety mechanism.

Artome M10 connection panel transmits HDMI and HdBaseT -video signals with a pass-through cable to and from the Epson projector.

The Artome M10 sound system is an active speaker system with two front speakers and a subwoofer for low bass (2.1 audio system). Artome M10 is equipped with a line out to attach external speakers or transfer signal to other sound systems. It also supports plug-and-play connections to microphones.

Sound is processed with Artome Digital Signal Processor (DSP) and amplified with embedded D-class amplifier. Sound from the HDMI and HDBaseT source is de-embedded by the Epson projector.

Artome HybriDock™ is an USB audio interface which converts analog audio sources, such as microphones to digital USB microphones and transmits USB audio from a laptop to the Artome M10 sound system.

Notice that the sound capacity depends on the room acoustics and size. Test if the Artome M10 sound system capacity is enough for the location. To amplify the sound with additional speakers or sound system, use the Audio Out connection

Use all wireless media adapters with an HDMI connection with Artome M10. For further information, view the manual of the preferred wireless media adapter you want to use with Artome M10. Ask for recommendations from your company IT department or Artome reseller.

Artome M10 enables easy use of any USB-powered camera and provides a connection for the USB speakerphones for easy videoconferencing. With Artome HybriDock™ you can use different laptops and operating systems without the need to install any additional drivers or software when using a HDMI/USB cable.

In videoconferencing setup, camera is typically installed on top of the Artome M10 with a magnet mounted camera leg and a 15 cm USB cable, which is included in the package.

Artome M10 enables an easy streaming solution for events and hybrid learning. While it produces a big image and sound locally, and amplified speeches with microphones. It also streams image and sound by using videoconferencing or streaming software.

In this use case, the web camera is typically installed on the camera stand shooting the presenter. It is connected with a long USB cable to Artome M10 or straight to the host computer. The speech microphone is transmitted by videoconference software using a Artome HybriDock feature, which transforms the analog audio to USB audio.

Artome M10 is not manufactured or intended to be used with a radio equipment.   You can connect an external radio equipment to Artome M10 and use it as a mobile audiovisual solution. Artome takes no responsibility if a radio equipment is used but can recommend devices manufactured by other vendors.

Packaging includes:

• Artome M10 with pre-installed Epson ultra-short throw projector

• Epson remote control

• 4 m HDMI-USB cable

• Magnet stand for USB camera with 15 cm flat USB 3.0 cable

• Artome M10 - Quick User Guide

• Artome M10 - Safety documentation

• Artome M10 carton box

Optional:

• Microphone with cable

• Wireless microphone receiver and transmitter

• USB camera

• USB microphone

• Camera leg with long USB cable

This chapter contains: 

• Description of the controls.

• Description of the light indicators

• Description of the available connections

You can find the control panel on top of the device. 

 You can find the connection panel behind the front door.

This chapter contains: 

• Instructions of how to connect additional devices like microphones, external sound system, Web camera, speaker phone.

• Instructions of how to adjust the image

Artome M10 is a mobile solution which operates also as a mobile rack for additional devices. In an all-in-one solution, dimensions of cabling are short and cable management is easy. For connecting additional devices see solution diagram below.

MIC1 and MIC2 connections are for analog microphones.

Before selecting a microphone for Artome M10 take the following subjects under consideration:

• Artome recommends dynamic cardioid (or hyper-/supercardioid) microphones to minimize feedback and optimize the sound pressure.

• When using microphones with cables, input gain is fixed and is optimized for dynamic microphones with an impedance of 350 ohm.

• Microphone input does not provide phantom power, so using condenser microphones will require additional phantom power supply.

• When using rack mounted wireless microphones, ensure that the microphone receiver depth is not more than 260 mm with the cable and the gain can be adjusted from the microphone system.

For preferred microphones and wireless microphone systems, ask your Artome reseller.

Artome includes stereo audio out connection for connecting additional sound systems or audio devices, such as recorders to Artome solution.

When Artome M10 is used for videoconferencing, it is preferred to use additional speakerphones. A speakerphone enables interactive discussion and there is no need for local speech reinforcement. In remote meeting a speakerphone also operates as a speaker system.

Artome recommends using speakerphones with Bluetooth USB dongles or long USB cables. Connect a wireless bluetooth USB-dongle or a USB cable to the USB connector of Artome M10 (image B) Be sure to charge the speakerphone and turn it off after use.

This chapter contains  information about:

• how to find the best location for the unit

• how to adjust the image size

• how to adjust the focus

• how to adjust the image shape (keystone adjustment)

• how to lift the image

To fully project the image, do not use the Artome M10 next to an object taller than 78 cm / 30.7 inches (see fig. 7).

To ensure proper air ventilation, leave at least 15 cm / 6 inches of free space on both sides of the Artome M10 during use.

To increase the image size, move M10 further away from the projection surface. See image below.

To decrease the image size, move M10 closer to the projection surface.

To adjust the image digitally,

1. Press Freeze.

2. To decrease image size, press Vol -

3. To increase image size, press Vol+.

4. To save the changes, press Freeze again.

1.  To open the front door, press the door at the upper left corner.

2.  Adjust the focus.

To correct an image that is slanted on the sides, use the projector's keystone correction buttons (see figure below).

To open the front door, press the door at the upper left corner.

1. To activate image lift, press Freeze.

2. To lift the image, press Volume -. This reduces the size of the image and raises the image

3. Move Artome M10 away from the projection surface. Image size increases.

4. To save the adjustment, press Freeze again.

1. Connect the power cord to the POWER connector at the back. 

2. To turn Artome M10 on, press the POWER button.

3. Connect a laptop for testing.

4. Feed the HDMI-USB cable through the inlet and connect the cable to the Artome HDMI 1 and ARTOME + connectors (image B). If the laptop is using wireless sharing or wireless collaboration, ask for user instructions from IT department or Artome reseller.

5. Connect the HDMI connector to your computer. Use suitable adapter if necessary.

6. To select source, if there are multiple sources connected simultaneously, press the SOURCE button.

7. To play content with sound from laptop and adjust the sound level of Artome M10, if needed press the Volume up/down buttons.

8.To use a camera or speakerphone, connect the USB end of the cable to your computer (image C).

This chapter contains information about: 

• connecting the unit

• video conferencing

• streaming

• audio

1. Connect the HDMI cable to your laptop. Artome M10 powers on automatically when connected to HDMI1 input.

2. If there are multiple sources connected simultaneously, to select the source, press Source button.

3. Use Freeze or Pause if necessary.

If laptop is not detected within 20 minutes, Artome M10 shuts down.

Wireless sharing technology is not included as a default, but M10 can be easily connected to any wireless collaboration system with HDMI.

This manual does not include the operating instructions of other vendors. For further information, check additional guides from your reseller or IT department.

1. Connect the HDMI and USB cables to your laptop. Artome M10 power on automatically.

2. Check the settings of your videoconferencing software:

• Camera — The name of the USB camera. Use camera connected to Artome as the image source

• Speaker — The name of the speakerphone. Speakerphone plays back the video call audio

• Microphone — The name of the speakerphone. Use speakerphone as the audio source

1. Connect the HDMI and USB cables to your laptop. Artome M10 powers on automatically

2. Check settings of your videoconferencing software

• Camera — The name of the USB camera. Uses camera connected to Artome as the image source

• Speaker — ARTOME HybriDock. Artome speakers play back laptop content including the video call audio

• Microphone — ARTOME HybriDock. Uses Artome MIC 1 and MIC 2 connections as the audio source.

1. Connect the USB cable to your laptop

2. To power on Artome M10, press the On/Off button

3. Select Artome HybriDock as the laptop speaker

4. Adjust the volume with your laptop.

This chapter explains how to:

• manage cables

• clean the casing

• clean the projector including the lens

• follow the service program

• Disconnect any unnecessary cables and put them neatly inside the storage space.

• Make sure that the necessary cables are firmly connected and enter the casing through the cable grommet at the bottom.

• Clean the projector casing with a vacuum cleaner equipped with a crevice nozzle. Clean under the projector and around the fans on both sides of the cabinet.

• Clean the projector's lens periodically, or whenever you notice dust or smudges on the surface. Make sure you unplug the projector before cleaning the lens.

• To remove dust or smudges, gently wipe the lens with lens-cleaning paper.

• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens.

For any questions, information, technical assistance, service, or ordering user instructions, please contact first your local reseller or distributor. If the reseller and/or distributor cannot provide the required info, contact the manufacturer:

Artome Ltd | Syrjäläntie 81 | 19110 VIERUMÄKI | FINLANDTel: +358 40 455 4455 | e-mail: contact@artome.fi | www.artome.fi

The latest version of the user manual is available in the following address: http://www.artome.fi/M10/usermanual

Besides these user instructions, the following documentation is available:

• Artome M10 - Quick User Guide

• Declaration of Conformity

Ordering Documentation

For more information or additional documentation, please contact Artome by email: contact@artome.fi.

The documentation for this product is available in multiple languages, please contact us by email if you require another language.

Documentation Feedback

Any feedback about our documentation, please email us at contact@artome.fi.

We appreciate your comments.

This chapter informs about:

• disposal of electronic compnents

• disposal of packaging waste

The symbol on the product, the accessories or packaging indicates that this device must not be treated as unsorted municipal waste but must be collected separately! Dispose of the device via a collection point for the recycling of waste electrical and electronic equipment if you live within the EU and in other European countries that operate separate collection systems for waste electrical and electronic equipment. By disposing of the device in the proper manner, you help to avoid possible hazards for the environment and public health that could otherwise be caused by improper treatment of waste equipment. The recycling of materials contributes to the conservation of natural resources. Therefore, do not dispose of your old electrical and electronic equipment with the unsorted municipal waste.

The packaging is made of environmentally friendly materials, which may be disposed through your local recycling facilities. By disposing of the packaging and packaging waste in the proper manner, you help to avoid possible hazards for the environment and public health. The symbol on the packaging indicates that the packaging is made of PAP.